Chicago vs Dallas
Side-by-side FOG compliance comparison between Chicago, IL and Dallas, TX.
| Requirement | Chicago, IL | Dallas, TX |
|---|---|---|
| Plumbing Code | IPC (Chicago Building Code based on International Plumbing Code with local amendments) | IPC (Texas adopts IPC statewide; Dallas has local amendments) |
| Min. Trap Size | Grease interceptors sized per Chicago Building Code Section 18-29-1003.3.6 table; minimum 750 gallons for gravity interceptors for restaurants; hydromechanical grease interceptors rated at minimum 20 GPM for smaller facilities | Minimum 750 gallons for gravity grease interceptors for FSEs; sizing per Dallas City Code and Texas Plumbing Code based on fixture count; hydromechanical grease interceptors minimum 20 GPM for limited food prep operations |
| Pumping Frequency | Every 90 days minimum or when 25% full (whichever comes first) | Every 90 days minimum; more frequently if grease and solids exceed 25% of trap capacity |
| 25% Rule | Yes | Yes |
| Permit Required | Required | Required |
| Permit Fee | Sewer discharge permit required; FOG registration included with building/sewer permits. Permit fees vary based on discharge volume | Grease trap permit required through Dallas Water Utilities Pretreatment Program; fees vary |
| Max Fine | $1,000 per day per violation under Chicago Municipal Code; repeat offenders face escalating fines | $2,000 per violation per day under Dallas City Code; repeat violations subject to escalating enforcement including potential service disconnection |
| Inspections | Chicago Department of Water Management conducts inspections; frequency based on compliance history, typically annually for FSEs | Dallas Water Utilities Pretreatment Division conducts inspections; annually for permitted FSEs; more frequently for non-compliant facilities |
| Record Keeping | Yes | Yes |
| Authority | Chicago Department of Water Management | Dallas Water Utilities, Pretreatment Division |
| Establishments | 12,246 | 6,049 |
Key Differences
As cities in different states, Chicago (IL) and Dallas (TX) operate under distinct regulatory frameworks. Here are the most important differences restaurant operators should know:
- Chicago follows the Uniform Plumbing Code (UPC), while Dallas uses the Uniform Plumbing Code (UPC). This affects trap sizing calculations and installation standards.
- Pumping schedules differ: Chicago requires "Every 90 days minimum or when 25% full (whichever comes first)", whereas Dallas requires "Every 90 days minimum".
- Both cities enforce the 25% rule, requiring grease traps to be pumped when grease and solids reach 25% of the trap's capacity.
- Fines differ: Chicago penalties can reach $1,000 per day per violation under Chicago Municipal Code; repeat offenders face escalating fines, compared to $2,000 per violation per day under Dallas City Code; repeat violations subject to escalating enforcement including potential service disconnection in Dallas.
What This Means for Restaurant Operators
If you operate food service establishments in either city, understanding these regulatory differences is critical for compliance. Permit requirements vary, so check with each city's wastewater authority before opening a new location. Different plumbing codes (IPC (Chicago Building Code based on International Plumbing Code with local amendments) vs IPC (Texas adopts IPC statewide; Dallas has local amendments)) mean trap sizing calculations may produce different results for the same kitchen setup. Always verify current requirements directly with your local wastewater authority or plumbing inspector.
Frequently Asked Questions
How do grease trap requirements compare between Chicago and Dallas?
Chicago follows the Uniform Plumbing Code (UPC), while Dallas uses the Uniform Plumbing Code (UPC). This affects trap sizing calculations and installation standards. Pumping schedules differ: Chicago requires "Every 90 days minimum or when 25% full (whichever comes first)", whereas Dallas requires "Every 90 days minimum".
Which city has stricter grease trap enforcement, Chicago or Dallas?
Enforcement varies: both cities have similar permit requirements. Chicago fines: $1,000 per day per violation under Chicago Municipal Code; repeat offenders face escalating fines. Dallas fines: $2,000 per violation per day under Dallas City Code; repeat violations subject to escalating enforcement including potential service disconnection. Always verify with local authorities.
How do pumping schedules differ between Chicago and Dallas?
Chicago: Every 90 days minimum or when 25% full (whichever comes first). Dallas: Every 90 days minimum; more frequently if grease and solids exceed 25% of trap capacity.
Regulations change frequently. Always verify current requirements with your local wastewater authority or plumbing inspector before making compliance decisions. Last updated: March 2026.
Operating in Both Cities?
Use our sizing calculator to find the right grease trap for each location.
Open Calculator