Dallas vs San Antonio
Side-by-side FOG compliance comparison between Dallas, TX and San Antonio, TX.
| Requirement | Dallas, TX | San Antonio, TX |
|---|---|---|
| Plumbing Code | IPC (Texas adopts IPC statewide; Dallas has local amendments) | IPC (Texas adopts IPC statewide) |
| Min. Trap Size | Minimum 750 gallons for gravity grease interceptors for FSEs; sizing per Dallas City Code and Texas Plumbing Code based on fixture count; hydromechanical grease interceptors minimum 20 GPM for limited food prep operations | Minimum 750 gallons for gravity grease interceptors for FSEs; sizing per SAWS requirements and Texas Plumbing Code; smaller hydromechanical interceptors (20-50 GPM) allowed for limited food prep |
| Pumping Frequency | Every 90 days minimum; more frequently if grease and solids exceed 25% of trap capacity | Every 90 days minimum; SAWS Grease Trap Procedure Manual specifies cleaning must occur before grease and solids exceed 25% of trap capacity |
| 25% Rule | Yes | Yes |
| Permit Required | Required | Required |
| Permit Fee | Grease trap permit required through Dallas Water Utilities Pretreatment Program; fees vary | FOG permit/registration through SAWS; fees approximately $75-$200 annually |
| Max Fine | $2,000 per violation per day under Dallas City Code; repeat violations subject to escalating enforcement including potential service disconnection | $2,000 per violation per day under City of San Antonio ordinance; SAWS can also assess surcharges for non-compliance |
| Inspections | Dallas Water Utilities Pretreatment Division conducts inspections; annually for permitted FSEs; more frequently for non-compliant facilities | SAWS conducts routine inspections; typically annually for FSEs; increased frequency for repeat violators |
| Record Keeping | Yes | Yes |
| Authority | Dallas Water Utilities, Pretreatment Division | San Antonio Water System (SAWS) |
| Establishments | 6,049 | 4,282 |
Key Differences
Even though both cities are in Texas, their FOG compliance requirements can differ significantly at the municipal level. Here are the most important differences restaurant operators should know:
- Dallas follows the Uniform Plumbing Code (UPC), while San Antonio uses the Uniform Plumbing Code (UPC). This affects trap sizing calculations and installation standards.
- Pumping schedules differ: Dallas requires "Every 90 days minimum", whereas San Antonio requires "Every 90 days minimum".
- Both cities enforce the 25% rule, requiring grease traps to be pumped when grease and solids reach 25% of the trap's capacity.
- Fines differ: Dallas penalties can reach $2,000 per violation per day under Dallas City Code; repeat violations subject to escalating enforcement including potential service disconnection, compared to $2,000 per violation per day under City of San Antonio ordinance; SAWS can also assess surcharges for non-compliance in San Antonio.
What This Means for Restaurant Operators
If you operate food service establishments in both cities, understanding these regulatory differences is critical for compliance. Permit requirements vary, so check with each city's wastewater authority before opening a new location. Different plumbing codes (IPC (Texas adopts IPC statewide; Dallas has local amendments) vs IPC (Texas adopts IPC statewide)) mean trap sizing calculations may produce different results for the same kitchen setup. Always verify current requirements directly with your local wastewater authority or plumbing inspector.
Frequently Asked Questions
How do grease trap requirements compare between Dallas and San Antonio?
Dallas follows the Uniform Plumbing Code (UPC), while San Antonio uses the Uniform Plumbing Code (UPC). This affects trap sizing calculations and installation standards. Pumping schedules differ: Dallas requires "Every 90 days minimum", whereas San Antonio requires "Every 90 days minimum".
Which city has stricter grease trap enforcement, Dallas or San Antonio?
Enforcement varies: both cities have similar permit requirements. Dallas fines: $2,000 per violation per day under Dallas City Code; repeat violations subject to escalating enforcement including potential service disconnection. San Antonio fines: $2,000 per violation per day under City of San Antonio ordinance; SAWS can also assess surcharges for non-compliance. Always verify with local authorities.
How do pumping schedules differ between Dallas and San Antonio?
Dallas: Every 90 days minimum; more frequently if grease and solids exceed 25% of trap capacity. San Antonio: Every 90 days minimum; SAWS Grease Trap Procedure Manual specifies cleaning must occur before grease and solids exceed 2.
Regulations change frequently. Always verify current requirements with your local wastewater authority or plumbing inspector before making compliance decisions. Last updated: March 2026.
Operating in Both Cities?
Use our sizing calculator to find the right grease trap for each location.
Open Calculator